TORO LX LAWN TRACTOR SERVICE MANUAL Pdf Download | ManualsLib.Operator's Manuals

Looking for:

Service Manuals | Toro.Toro Groundsmaster D Mower Service Repair Workshop Manual DOWNLOAD - Service Manuals Club 

Click here to DOWNLOAD

     

- Find Manual & Parts List | Briggs & Stratton

 

Table Of Contents. Quick Links. Consumer Products. Table of Contents. Previous Page. Next Page. Heavy-duty triple turf flail mower, serial no. Page 3: Table Of Contents Installation Page 4 Installation Page 5 Electrical System Failure to comply The Toro Company Page 9: Specifications Fastener Identification Recommended fastener torque values are listed in the following tables. For critical applications, as determined by Toro, either the recommended torque or a torque that is unique to the application is clearly identified and specified in the service manual.

The specific torque value should be determined based on the fastener size, the aluminum or base material strength, length of thread engagement, etc.

All torque values are based on non- lubricated fasteners. Conversion Factors in-lb X Page Chassis 3. Remove the deck rod from the deck hanger bracket Fig. Fig PICT 6. Remove the hood from the frame Fig. Fig PICTa 4. Raise the hood Fig. Page 16 Remove and discard the cotter pins from the two axles Fig. Page 17 Bushing stays in rim of tire Fig. Remove the nut securing the ball joint to the axle assemblies Fig.

Bushing stays on axle Fig. Page 18 Remove the cap from the axle assembly Fig. Remove the axle assembly from the front pivot axle Fig.

Repeat steps to remove the second axle. Page 19 Remove the nuts from the 2 bolts securing the pivot Cut the electrical tape securing the wire harness to axle and deck hanger bracket to the frame Fig. Page 20 Remove one of the bolts securing the deck hanger plate and pivot axle to the frame Fig. Page Installation Fig. Remove the front pivot axle Fig. Position the pivot bar bracket to the front pivot axle Fig. Position the deck hanger plate to the pivot axle and install a shoulder bolt Fig.

Page 23 Fig. Page 24 Position the ball joint into the axle assembly Fig. Page 25 Slide the wheel and tire assembly onto the axle Note: The wheel bearing is installed in the rim. Page 26 Apply grease to the wheel bearing Fig. Install a cotter pin into the axle assembly Fig. Install the hub cap Fig. Connect the positive and then the negative battery cable. Check the toe-in measurement and adjust as need- ed. Remove the wheel and tire assembly from the axle assembly Fig.

Fig PICT 3. Remove the cotter pin from the axle assembly Fig. Page 29 Bushing stays in rim of tire Fig. Remove the nut securing the ball joint to the axle assembly Fig.

Bushing stays on axle assembly Fig. Page 30 Remove the axle assembly from the axle pivot Fig. Page Installation 4. Install a nut onto the ball joint and torque to Page 32 8. Install a cotter pin into the axle pivot Fig. Slide the wheel and tire assembly onto the axle assembly Fig. Page Steering Wheel Replacement Fig PICT 2. Remove the bolt and washer securing the steering wheel to the steering shaft Fig. Fig PICT Lower the machine. Page 34 3. Install the steering wheel cap Fig.

Position the front tires so that they are pointing straight forward. Slide the steering wheel onto the steering shaft Fig. Page 36 7. Remove the two screws securing the fuel tank steering shaft Fig. Page Installation 5. Slide the pinion onto the steering shaft Fig. Page 39 7. Grease the pinion gear with 2 general purpose Position the fuel tank support rods and install two grease Fig. Page 40 Page 41 2. Raise the tractor so the clutch can be accessed.

Unplug the clutch from the wire harness Fig. Remove the clutch and washer s from the crank- shaft Fig. Install the bolt and lock washer securing the clutch to the crankshaft. Torque the bolt to Lay the washer s on top of the clutch Fig. Page Removal 2. Remove the fuel tank from the engine compartment Fig. Position the fuel tank support rods and install screws to secure the fuel tank Fig. Page Hood Replacement 1. Lower the hood Fig. Unplug the headlights from the wire harness Fig.

Page Installation 2. Plug the headlights to the wire harness Fig. Position the hood on the chassis Fig. Remove the battery from the battery tray Fig.